A forearm wiping a wet car window with a grey microfibre towel, a spray bottle on a cart at the left
Guide

How to prep glass for tint

To prep glass for tint, walk the job first: inspect each pane, record chips, scratches and existing film, clean in a fixed order, then check under bright light before film goes on the glass. Decline a pane when you are unsure. Glacier supplies window film and installation tools to tint shops and installers.

Prep method at a glance

General trade practice, not a Glacier procedure. To prep glass before installing window tint, inspect each pane and record chips, scratches and old film, clean in a fixed order, scrape gently where the glass allows, wipe the glass down again, then check under raking light before film goes on.

  • Record chips, cracks, scratches, old film or adhesive, defroster lines and loose seals before cleaning.
  • Pause or decline a pane when you cannot explain a crack, identify the glass or remove old film cleanly.
  • Glacier supplies window film and installation tools to tint shops and installers.
  • Apply for a wholesale account, and a Glacier rep will follow up.

What should I check before I touch the glass?

Walk the job before any water or scraper is used. What you find changes the quote and protects the shop if a customer later asks what was already there.

For buildings, add the frame, the seal and the glass type to this walkaround. Ask the window maker what the pane is and whether film is allowed.

Comparison
What you findWhy it mattersWhat to do
Chips and cracksThey show through film and can be mistaken for new damageRecord them and tell the owner before you start
ScratchesFilm does not hide themRecord them before cleaning so the glass is documented
Old film or adhesiveIt has to come off before new film goes onPlan removal on the quote; see the tint removal guide
Rear glass defroster linesThey are easy to damage with a scraperWork gently around them
Loose seals and gasketsThey let water and dirt back onto clean glassNote them and tell the owner
Unknown or replaced glassYou cannot tell its historyAsk the owner, and ask the glass maker if the pane is in question

In what order should I clean the glass?

A fixed order keeps dirt from moving back onto glass you already cleaned. Scrape the inside only where the glass allows it, ask the owner about coated glass, and follow the glass prep guide linked below for the cleaning order, products and technique.

Gloved hand wiping a sprayed car window with a lint-free cloth in the bay

What changes between side, rear and front glass?

Different panes raise different questions. Walk each one rather than assuming they are all the same.

Comparison
PaneWatch forPrep note
Side glassSeals, gasket lines and inside edgesIf the gasket moves freely, ease it clear and wipe under it
Rear glassDefroster lines, curve and cornersWork gently around them
Windshield strip or front glassAnything fixed to the glass, such as mounts or sensorsAsk the owner what is attached before you start
Building glassFrame, seals and glass typeAsk the window maker what the pane is

How do I make prep repeatable?

Prep is the step most likely to be rushed. Write it down once and use it on every job.

  • Keep a one-page walkaround sheet with a line for each pane.
  • Keep prep tools in one kit so nothing is borrowed from another job.
  • Use clean towels on the film side and keep wash towels apart.
  • Run the same final light check on every pane.
  • If a pane fails the check, clean it again before you lay film.
Gloved hand holding a lint-free towel against the edge of a car window, one side clean and one side damp

How do I clean edges, corners and gaskets?

Edges are where most dirt hides. A clean center with a dirty edge still puts a speck under the film.

  • Use a narrow tool or card wrapped in a clean towel to reach the edge.
  • If the gasket moves freely, pull the gasket line gently clear and wipe under it.
  • Wipe each edge in one direction so dirt leaves the pane.
  • Check corners last, because water collects there.
Gloved hands spraying cleaning solution on the sunroof edge of a bronze wagon and scrubbing the edges with a pad.

How do I know the glass is clean enough?

Judge the glass the way the customer will see it, from an angle and in bright light.

  • Hold a bright handheld light low across the pane and look for specks, hair and lint.
  • Look from the inside and the outside.
  • Wipe the scraper path once more and look again.
  • If you find dirt after the final wipe, clean the pane again rather than hoping film covers it.

When should I decline or pause a pane?

Declining a pane is better than guessing. Pause the job and speak to the owner when the glass raises a question you cannot answer.

Comparison
TriggerPause or declineWho to ask
A crack you cannot explainPauseThe owner
Old film that will not come off cleanlyPause and re-quoteThe owner
A pane you cannot identifyPauseThe glass or window maker
A seal that is failingRecord, then decideThe owner
Conditions that keep putting dirt on clean glassFix the bay firstYour shop team

What do I tell the owner before and after prep?

A short written note protects both sides.

  • What you found on each pane before cleaning.
  • What film cannot fix, such as chips and scratches.
  • Any extra work, such as old film removal, and why it is on the quote.
  • Which panes you paused or declined, and the reason.
  • Ask the owner to initial the condition note before work starts.
A gloved hand wiping a window clean with a microfiber cloth in a tint bay, soap droplets on the glass.

Which tools help with glass prep?

Prep uses scrapers, blades, cards, towels and spray bottles. Tools are listed here by category only.

Glacier supplies installation tools and window film to tint shops and installers. Apply for a wholesale account, and a Glacier rep will follow up.

  • Scrapers and blades: see the blades and scrapers category.
  • Prep and slip supplies: see the prep and slip category.
  • A bright handheld light for the final check.
In this guide
  1. Prep method at a glance
  2. What should I check before I touch the glass?
  3. In what order should I clean the glass?
  4. What changes between side, rear and front glass?
  5. How do I make prep repeatable?
  6. How do I clean edges, corners and gaskets?
  7. How do I know the glass is clean enough?
  8. When should I decline or pause a pane?
  9. What do I tell the owner before and after prep?
  10. Which tools help with glass prep?

Quick answers

10 questions. Select one to open it.

How do you prep glass for tint?

Inspect each pane, record chips, scratches and old film, protect the interior, clean the outside and inside in a fixed order, scrape gently, clean again and check under bright light before film goes on the glass.

What should I inspect on glass before tinting?

Look for chips, cracks, scratches, old film or adhesive, defroster lines and loose seals. Record them before cleaning so the condition of the glass is on file.

What do I record before cleaning?

Record chips, cracks, scratches, old film or adhesive, defroster lines and loose seals on a written condition note before you wash or scrape. Ask the owner to initial the note before work starts.

How do I clean the edges of the glass for tint?

Wrap a clean towel around a narrow tool or card, ease the gasket line clear and wipe each edge in one direction. Check the corners last.

How do I check the glass is clean enough for film?

Hold a bright light low across the pane and look from both sides for specks, hair and lint. If anything shows after the final wipe, clean it again.

When should I decline a pane?

Decline or pause when you cannot explain a crack, cannot identify the glass, or cannot remove old film cleanly. Declining is better than guessing.

Should I take photos before I start?

A written condition note is the least you should do. Some shops add photos as well. Whichever you use, record the glass before cleaning and ask the owner to initial it.

Do I clean old film residue the same way?

Old film and adhesive have to come off before new film. Plan it as its own step on the quote and see the tint removal guide.

How is prepping building glass different from car glass?

You also check the frame, the seal and the glass type. Ask the window maker what the pane is and whether film is allowed on it.

Does Glacier supply tools for glass prep?

Glacier supplies installation tools, including scrapers, blades and prep supplies, to shops and installers. Apply for a wholesale account, and a Glacier rep will follow up.

Need installation tools for your shop? Apply for a wholesale account.